Advice from Hank – Installing a Bathroom Vanity, Sink and Faucet

With the cold weather upon us, you may want to tackle those indoor remodeling projects. Installing a new bathroom vanity, sink and faucet is an easy way to give your bathrooms a fresh look. This project won’t put your bathroom out of commission for too long either.

Before you get started, you will need these tools:Hank Ready to Install a Vanity

– Adjustable wrench
– 3″ drywall screws
– Pipe Wrench
– Tape measure
– Carpenter’s level
– Stud finder
– Shims
– Utility knife
– Hole saws
– Drill
– Caulking gun and caulk

Step 1: Find out how the old vanity is attached.

The first thing your need to do is get rid of the sink or vanity that’s already in your bathroom and get the space ready for your new vanity. Check under the vanity to see how it’s attached – probably with some screws through a rail on the back (often called a “nailer”), or in the corners. While your head is under the countertop, look to see how your countertop and sink are attached to the base. Again, there may be screws holding the top in place, or it may just be held in place with glue.

Removing your old vanity will be easier if you take off the top (it will be lighter). Finally use a utility knife and run the blade around the edge, cutting through any caulking holding the vanity edges to the walls or backsplash.

Step 2: Remove the Old Vanity

As in any plumbing project, turn off the water to your bathroom. Hopefully, this means closing the shut off valves on the water feed lines to the vanity, but in some cases it might mean you need to shut off the water to the whole house. You’ll need an adjustable wrench to disconnect the supply tubes from the faucet bases, and a pipe wrench to undo the drain. Special tip: It’s a good idea to have a bucket handy when you open the drain to catch the water that’s remaining in the trap.

Take off the doors and remove the drawers from the vanity. Now take out the screws holding the vanity to the wall, and if you’re going to take off the top, undo the screws holding it in place or use a pry bar to break it away from the base.

You should be able to slide the vanity out and away from the wall, but in some cases you may have to pry it away from the wall. If you do, use a thin scrap of wood to protect the wall from the pry bar. It’s a good idea to put down a thin sheet of plywood or even an old blanket to prevent gouging your floor when sliding the vanity.

Once you’ve removed the old vanity, inspect the area for any damage.

Step 3:  Measuring for the New Vanity

Measure the height and width of your new vanity. Determine where you want to position it and mark the edge locations with vertical lines. Now, measure and mark up from the floor in three places the height of your vanity. Use the highest mark and draw a level line through it, joining the two vertical lines.

Measure the locations of the water pipes and drain lines coming out of the wall and transfer those measurements onto the back of your vanity. Use a hole saw (at least 1/2″ larger than the pipes) and drill holes for your water lines. Cut the cutout for the drain with a larger hole saw or a saber saw.

Verify where at least one stud is in the wall behind your new vanity, measure and mark its location on the vanity nailer, and drill a pilot hole for the 3″ screw that will hold it in place.

Step 4: Installing the New Vanity

Make the vanity easier to move by taking out doors and drawers. This will minimize damage to the vanity and bathroom.

Protect your floors and move the vanity into position, then slide it into place with the water and drain pipes coming through the holes you cut in the back. Check that the cabinet is level (both side to side and front to back), and use shims to level it if necessary. Once the vanity is level, attach it to the wall using 3″ screws.

Step 5: Putting on the top and sink

Check your vanity to see if you need to install these components before putting it on the wall. Start by putting the faucet through the precut holes and hand tighten them. Now turn the vanity top over and use a wrench to firm them up. Attach flexible water supply lines to the base of the faucet and the tail pipe to the sink drain. Finally spread a bead of silicone caulk all around the edge of the countertop, then turn it over and position it on the vanity with the backsplash tight against the wall.

If you’re putting a separate sink into your new vanity, you will need to install the countertop first, then install the faucets to the sink, and finally put the sink into the countertop.

Step 6: Plumbing touch ups

Attach the flexible feed lines to the water supply valves and connect the sink tailpiece to the trap and drain. Run a small bead of caulk around the base of the faucet and where the vanity top butts against the backsplash, and then install moldings around the base of the vanity. After you check the seals, you can turn the water on and examine the faucet and vanity for leaks.

Shop at your local Hardware Hank to save.  #DIYToday

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s